|
|
Corrosion resistance of cast duplex stainless steels
Müller, Peter ; Záděra, Antonín (referee) ; Pernica, Vítězslav (advisor)
The master’s thesis deals with corrosion resistance of cast duplex steels. In the first part the corrosion mechanisms and their individual types are described, the second part characterizes the types of stainless steels in terms of their properties, use, structural components, and their impact on mechanical and corrosion properties of steels. Individual chapter is dedicated to duplex steels. In the experimental part the resistance of 1.4517 steel against pitting corrosion depending on the alloy contents and the PREN value was investigated. Four specimens graded according to PREN were cast. Supplemented with sample stirrer blade which was affected by corrosion during service they were subjected to corrosion test according to ASTM G48-11 standard in 6% FeCl3 solution. Cast specimens were subjected to tensile test and impact test.
|
|
|
Influence of a particullar heat on properties and structure of duplex steel welded joint
Němec, Karel ; Kubíček, Jaroslav (referee) ; Daněk, Ladislav (advisor)
The research project is focused on an influence of a particullar heat on properties and structure of duplex steel DIN 1.4462. Samples prepared by using different welding speeds 10, 15, 20, 25, 30 cm.min-1, were tested for tensile, metalographical analysis and hardness test. Experimental results proved the optimal welding speed for material with 2 mm thickness to be 15 cm.min-1. Usage of lower speed 10 cm.min-1 led to formation of hot cracks while higher speeds 20, 25, 30 cm.min-1 didn‘t cause material penetration.
|
|
| |
|
|
Influence of chemical composition of steel on structure and properties of stainless steels
Valenta, Pavel ; Čech, Jan (referee) ; Záděra, Antonín (advisor)
The thesis is focused on high-alloy austenitic and austenitic-ferritic (duplex) steel. The theoretical part includes research about high-alloy steels and basic introduction to this issue. In the practical part of the test there were casted refractory austenitic steel 30CH3N17G2L, duplex stainless steel 1.4462, low carbon steel and high carbon steel. On the castings of austenitic steel were made mechanical and technological tests. There were evaluated the effects of different casting temperature and casting wall thickness to the microstructures and macrostructures of steel, tensile strength and charpy impact tests. The technological tests compared technological properties of these steels.
|
|
|
Corrosion resistance of cast duplex stainless steels
Müller, Peter ; Záděra, Antonín (referee) ; Pernica, Vítězslav (advisor)
The master’s thesis deals with corrosion resistance of cast duplex steels. In the first part the corrosion mechanisms and their individual types are described, the second part characterizes the types of stainless steels in terms of their properties, use, structural components, and their impact on mechanical and corrosion properties of steels. Individual chapter is dedicated to duplex steels. In the experimental part the resistance of 1.4517 steel against pitting corrosion depending on the alloy contents and the PREN value was investigated. Four specimens graded according to PREN were cast. Supplemented with sample stirrer blade which was affected by corrosion during service they were subjected to corrosion test according to ASTM G48-11 standard in 6% FeCl3 solution. Cast specimens were subjected to tensile test and impact test.
|
|
| |
|
|
Influence of chemical composition of steel on structure and properties of stainless steels
Valenta, Pavel ; Čech, Jan (referee) ; Záděra, Antonín (advisor)
The thesis is focused on high-alloy austenitic and austenitic-ferritic (duplex) steel. The theoretical part includes research about high-alloy steels and basic introduction to this issue. In the practical part of the test there were casted refractory austenitic steel 30CH3N17G2L, duplex stainless steel 1.4462, low carbon steel and high carbon steel. On the castings of austenitic steel were made mechanical and technological tests. There were evaluated the effects of different casting temperature and casting wall thickness to the microstructures and macrostructures of steel, tensile strength and charpy impact tests. The technological tests compared technological properties of these steels.
|
|
|
Influence of a particullar heat on properties and structure of duplex steel welded joint
Němec, Karel ; Kubíček, Jaroslav (referee) ; Daněk, Ladislav (advisor)
The research project is focused on an influence of a particullar heat on properties and structure of duplex steel DIN 1.4462. Samples prepared by using different welding speeds 10, 15, 20, 25, 30 cm.min-1, were tested for tensile, metalographical analysis and hardness test. Experimental results proved the optimal welding speed for material with 2 mm thickness to be 15 cm.min-1. Usage of lower speed 10 cm.min-1 led to formation of hot cracks while higher speeds 20, 25, 30 cm.min-1 didn‘t cause material penetration.
|
guest ::
